SG Power Product Pvt. Ltd.
SGP/Blog/Oil Cooled Servo Stabilizer Maintenance

Oil Cooled Servo Stabilizer Maintenance: Oil Level, BDV Test and Checklist

By the SG Power technical team · Updated November 2026 · 18-minute read

Oil cooled servo stabilizer maintenance comes down to four jobs: check the oil level and look for leaks every month, check the connections every six months, and once a year test the oil, inspect the carbon brushes and have the unit serviced and calibrated. The oil is what sets it apart from an air cooled unit.

If you run a three phase oil cooled servo voltage stabilizer in a factory, CNC shop, hospital or large building, this guide shows how to maintain it: each job, who should do it and how often. Regular upkeep cuts downtime and adds years to the unit's service life. The guide applies to every oil cooled servo stabilizer from 60 kVA to 500 kVA.

Oil cooled servo stabilizer with cooling radiators on the tank sides

What Is an Oil Cooled Servo Stabilizer?

An oil cooled servo stabilizer is a servo voltage stabilizer whose transformer and variac sit in a tank of insulating oil. The oil carries heat away and insulates the windings, so the unit can run heavy loads round the clock. In SG Power's range, oil cooled units run from 60 kVA to 500 kVA.

Why Does an Oil Cooled Servo Stabilizer Need Different Care?

An oil cooled servo stabilizer needs different care because its oil does two jobs: it carries heat away from the windings, and it insulates them. If the oil level drops or the oil takes in moisture, both jobs suffer. The unit is also called an oil immersed or oil filled servo stabilizer.

Inside the tank sit the buck-boost transformer and the variac, which a servo motor drives to correct every voltage fluctuation in the mains.

The tank sheds the oil's heat through the cooling radiators on its sides, so keep them clean and do not stack material against them.

An air cooled servo stabilizer has no oil, so its upkeep is dusting and brush checks. An oil cooled unit needs those too, plus oil checks. In return it copes with dust, heat, humidity and round-the-clock running, which is why larger and industrial units are built this way. For the electrical side, see how a servo stabilizer works.

What Is the Maintenance Schedule for an Oil Cooled Servo Stabilizer?

An oil cooled servo stabilizer needs weekly reading checks, monthly oil level and leak checks, six-monthly connection checks and a yearly oil test, brush inspection and full service. This is preventive maintenance: small, regular checks that stop faults before they start.

TaskHow oftenWho
Check input and output readings on each phaseWeeklyUser
Check the oil level and look for leaksMonthlyUser or electrician
Dust the body and cooling radiators, and keep the area around the tank clearMonthlyUser
Check for loose connections and heating marksEvery 6 monthsElectrician
Test the oil's breakdown voltage (BDV); top up or filter as advisedYearlyTrained technician
Scan terminals and joints for hot spots with a thermal camera, where availableYearlyTrained technician
Test insulation resistance with a meggerYearlyTrained technician
Inspect and replace worn carbon brushesYearly, or if correction slowsTrained technician
Full service and calibrationYearly, or under an AMCSG Power service

What to read on the display each week

The front panel of an SG Power servo stabilizer shows the figures you need for the weekly check:

  • Phase-to-neutral voltage on each phase.
  • Phase-to-phase voltage.
  • Frequency.
  • Output load current on each phase.

Note them in the service log. The output voltage should hold steady, and the current on each phase should stay below the rated figure for your size.

Compare the current on the three phases as well. A large difference between phases points to an unevenly spread load, and the heavier phase will run hotter. Our guide on balanced vs unbalanced servo stabilizers explains why that happens and what to do about it.

What Are the Safety Rules for Servicing an Oil Cooled Servo Stabilizer?

Follow five safety rules when servicing an oil cooled servo stabilizer, because the unit carries high current and holds a tank of oil.

1

Isolate first. Switch the unit off, isolate the supply and lock the isolator before any work inside the cabinet.

2

Never tighten a live terminal. Connection checks are done with the supply off, by an electrician.

3

Leave the tank closed. Opening the tank, sampling and draining oil are jobs for a trained technician.

4

Keep oil off the floor and away from flame. Wipe up any spill at once, and hand drained oil to a waste oil recycler authorized under the pollution control board rules.

5

Do not keep resetting a trip. Find the cause first. On bypass the load runs unprotected, so use it only while the fault is being fixed.

The user's part is the outside of the unit: readings, oil level, leaks and dusting. Everything inside belongs to an electrician or technician.

How Do You Check the Oil Level in an Oil Cooled Servo Stabilizer?

Check the oil level of an oil cooled servo stabilizer once a month, and before the first switch-on of a new unit. It takes a few minutes and needs no tools. Here is how to check the oil level in a servo stabilizer, step by step.

1

Read the oil level on the gauge and compare it with the marked level.

2

Look at the tank seams, drain valve and gaskets for wet patches or drips.

3

Look at the floor under the unit for oil stains.

4

If your unit has an oil temperature indicator, note its reading too.

5

Note the readings and the date in the service log.

A level that falls between checks means a leak, even if you cannot see one. Do not keep topping up without finding the cause. Call a technician.

What Is the BDV Test for Servo Stabilizer Oil?

The BDV test is a yearly oil test that measures the oil's breakdown voltage (BDV), also called its dielectric strength. This is the voltage at which the insulating oil stops insulating. Clean, dry oil has a high BDV. Oil that has taken in moisture or dirt has a lower one.

A trained technician draws a sample from the tank and tests it. What happens next depends on the result:

BDV resultWhat it meansAction
At or above the pass value on the test reportThe oil is in good conditionNo action; test again next year
Below the pass valueThe oil has taken in moisture or contaminationFilter the oil (oil filtration) and test again
Still low after filteringThe oil has reached the end of its lifeReplace the oil

The pass value in kV depends on the oil and the unit, so ask for it in writing. An SG Power test report states the pass value alongside the reading, so you can see at a glance which side of it your oil sits on.

For a large, old or critical unit, a laboratory can test more than BDV: moisture content, acidity and colour. Oil that has turned dark brown is ageing. Read the results as a trend from year to year, not as a single figure.

Is your oil test due? Book a service visit and we will test the oil and tell you what it needs.

Which Oil Should You Use to Top Up a Servo Stabilizer?

Top up an oil cooled servo stabilizer only with new mineral insulating oil that meets IS 335, the Indian Standard for transformer oil published by the Bureau of Indian Standards. Ask SG Power for the grade recommended for your unit before you buy any oil.

Three rules keep the oil sound:

Never use old or recovered oil. It may carry moisture into the tank.

Keep the oil sealed until use. Oil left open absorbs moisture from the air.

Ask for the oil quantity in writing. It differs by size and design, so get the exact figure for your unit from the manufacturer.

What Else Needs Checking Besides the Oil?

Besides the oil, an oil cooled unit needs the same servicing as any servo stabilizer: connections, carbon brushes and calibration.

Connections. Every six months, have an electrician check the input and output terminals for looseness and heating marks. A loose joint runs hot, and these units carry high currents.

Carbon brushes. The brushes ride on the variac (also called the dimmer) and wear with use, faster where voltage fluctuations are frequent. Have them inspected once a year, or sooner if the unit corrects more slowly than before.

Protections. The yearly service also tests the cut-offs for overload, over voltage, under voltage and phase failure.

Calibration. A yearly service checks that voltage regulation still holds the output within ±1%.

Earthing. Check that the body earth connections are tight and that the earth pit still gives a low reading. The earthing rules are in our servo stabilizer installation guide, and electrical work should follow the CEA safety and electric supply regulations.

Not sure when your unit was last serviced? Send us its rating and serial number, and we will tell you what is due.

What Is the Rated Current of Each Oil Cooled Size?

The rated current of an oil cooled servo stabilizer runs from about 83 A per phase at 60 kVA to about 696 A per phase at 500 kVA. During the weekly check, compare the current shown on the display with the figure for your size. A reading above it means the unit is overloaded.

SizeRated current per phase at 415 VSafe running load
60 kVA83.5 AAbout 38.4 kW
75 kVA104.3 AAbout 48 kW
100 kVA139.1 AAbout 64 kW
125 kVA173.9 AAbout 80 kW
150 kVA208.7 AAbout 96 kW
200 kVA278.2 AAbout 128 kW
250 kVA347.8 AAbout 160 kW
400 kVA556.5 AAbout 256 kW
500 kVA695.6 AAbout 320 kW

Safe running load is the kVA rating at a 0.8 power factor, less a 25% margin for motor starting. Every size is a 3 phase servo stabilizer, and all of them are listed on the servo stabilizer page. If you are sizing a new unit rather than checking an old one, our guide on how to calculate servo stabilizer kVA shows the method.

Maintenance Notes by Size: 60 kVA to 500 kVA

The schedule is the same for every size, but the practical work changes with size.

60 kVA to 100 kVA

These are the smallest units in the oil cooled range, and a plant electrician can do the monthly and six-monthly checks. The 60 kVA oil cooled servo stabilizer and the 75 kVA servo stabilizer often stand on the shop floor, so keep the area around the tank clear and watch for knocks to the valve and gauge. The 100 kVA servo stabilizer is common in small factories and hospitals, where it usually runs long hours; do not skip its yearly oil test.

125 kVA to 250 kVA

At these sizes the currents are high, so joints matter most. On a 125 kVA servo stabilizer or a 150 kVA oil cooled servo stabilizer, a loose lug shows up quickly as a heating mark. The 200 kVA servo stabilizer and the 250 kVA servo stabilizer usually feed a whole plant, so plan the yearly service for a shutdown or a low-load day and use the bypass.

400 kVA and 500 kVA

The 400 kVA servo stabilizer and the 500 kVA oil cooled servo stabilizer hold the most oil and carry the highest currents. Treat their upkeep as you would a transformer's: keep a written log, fix the service date in the plant's shutdown calendar, and have the oil test and service done by the manufacturer's team.

Servo Stabilizer Troubleshooting: What Do the Display Messages Mean?

An SG Power servo stabilizer switches its output off and shows a message when it detects an overload or a wrong phase sequence. Both clear once the cause is removed and the START button is pressed.

Display messageWhat it meansWhat to do
OverloadThe load current has gone above the set limit, and the output has been switched off to protect the unitReduce the load, then press START
Ph. ReversalThe phase sequence of the incoming supply is wrongHave an electrician interchange the incoming phases, then press START

The unit also cuts off on input over voltage, input under voltage and loss of a phase. If any message keeps coming back, do not keep resetting it. Find the cause, or call a technician.

What Problems Do Users Report, and What Should You Check First?

The servo stabilizer problems users raise most often on Indian engineering and consumer forums come down to six causes: an input outside the working range, normal correction time, loose connections, heat, a worn brush, and neglected oil. Check these before you call for service.

What users reportLikely causeWhat to check first
The output cuts off when the mains is very low or very highThe input has gone outside the stabilizer's working range, so the unit protects the load by switching offRead the input voltage on the display and compare it with the input range on the nameplate
The voltage takes a few seconds to settle after a dipNormal for a servo stabilizer, because a motor moves the brush to correct the voltageNothing, unless correction has become slower than it used to be
A new humming or vibrating noiseLoose connections, loose bolts or wear in the moving partsWith the supply isolated, have an electrician check terminals and fixings
The unit runs hotOverload, blocked airflow around the tank, or a hot roomCompare the load current with the rated current table above, and clear the space around the radiators
The servo motor keeps moving and the output huntsThe mains is swinging rapidly, or the carbon brush or its contact surface is worn or dirtyWatch the input voltage on the display. If the input is steady, call a technician
The oil test failsMoisture or contamination in the oilHave the oil filtered or replaced, as the test result calls for

A stabilizer corrects the voltage within its input range only. If your supply regularly goes outside that range, the fix is a model with a wider input range, so tell the manufacturer the lowest and highest voltage you record.

When Should You Check an Oil Cooled Servo Stabilizer More Often?

Check an oil cooled servo stabilizer more often in five situations: summer heat, monsoon humidity, a dusty plant, 24x7 running near full load, and after new machines are added. The schedule above is the baseline for normal conditions.

SituationWhy it mattersWhat to do more often
Summer, or a hot roomA high ambient temperature makes the oil and windings run hotterOil level, load current, clear space around the radiators
Monsoon, or a humid siteOil takes in moisture fasterLeak and gasket checks; test the oil before and after the season
A dusty plantDust settles on the radiators and holds heat inMonthly dusting becomes fortnightly
Running 24x7 near full loadBrushes and joints wear fasterConnection and brush checks
New machines addedThe load may have outgrown the unitCompare the load current with the rated current table

Which Warning Signs Need a Technician?

Call a technician if the stabilizer shows any of these six signs between services.

1

The oil level has fallen, or there is oil leakage on the tank or floor.

2

A terminal or cable lug shows discolouration or a heating mark.

3

The unit hums louder than usual or makes a new noise.

4

The output drifts outside ±1%, or correction has become slow.

5

The unit trips on overload when the load has not changed.

6

There is a burning smell.

Do not open the tank or drain oil yourself. Switch to bypass if the load must keep running, and note what you saw and when.

Seen one of these signs? Call +91 8929722150 or send us the details, and a service engineer will guide you.

Oil Cooled Servo Stabilizer Maintenance Checklist

Use this oil cooled servo stabilizer maintenance checklist at each visit, and file the completed sheet with the service log. It follows the preventive maintenance schedule above.

Weekly (user)

  • Input and output voltage noted on each phase.
  • Load current noted on each phase, and the three phases compared.
  • No alarm or message on the display.
  • No new noise, smell or heat.

Monthly (user or electrician)

  • Oil level within the marks on the gauge.
  • No oil on the tank, valve, gaskets or floor.
  • Body and cooling radiators dusted; space around the tank clear.

Every 6 months (electrician, supply isolated)

  • Input, output and earth connections tight.
  • No discolouration or heating marks on terminals and lugs.

Yearly (trained technician)

  • Oil sample tested for BDV; result recorded.
  • Insulation resistance tested; result recorded.
  • Carbon brushes inspected; worn brushes replaced.
  • Brush contact surface clean and smooth.
  • Output voltage and protections checked and calibrated.
  • Next service date entered in the log.

What Does Oil Cooled Servo Stabilizer Maintenance Cost?

The cost of maintaining an oil cooled servo stabilizer depends on six things, so it is quoted for each site and not from a fixed list:

1

The kVA rating, because a larger tank holds more oil.

2

Whether the oil needs only a test, filtration or full replacement.

3

Whether carbon brushes or other parts need replacing.

4

The number of visits in the year.

5

The distance of the site from the service centre.

6

Whether the work is a one-off call or part of an AMC.

Planned work costs far less than a breakdown. Replacing a worn brush at a yearly service is a small job. Repairing a burnt contact surface and an overheated cable after a failure is not. Ask SG Power for a maintenance or AMC quote for your size and site. If you collect more than one offer, our guide on how to compare servo stabilizer quotes shows what to look for beyond the price.

Should You Take an AMC or Maintain It In-House?

Split the work: do the simple checks in-house and leave the yearly work to trained technicians, under an AMC if you prefer a fixed arrangement.

WorkIn-houseManufacturer or AMC
Weekly readingsYes
Monthly oil level and leak checkYes
Six-monthly connection checkYes, by an electrician
Yearly oil test, top-up or filteringYes
Brush inspection and replacementYes
Full service and calibrationYes

SG Power supports its units through a service network in 127+ cities. If your unit is out of warranty, ask about an AMC when you get in touch, and whether it covers spare parts as well as labour.

Should You Repair or Replace an Old Unit?

Repair an old servo stabilizer when a wearing part has failed. Replace it when the unit itself no longer fits the job.

Repair it whenReplace it when
Brushes, gaskets or a control card have worn outThe load has outgrown the kVA rating
The oil needs filtering or changingBreakdowns keep coming back
A terminal or cable lug needs remakingThe repair costs nearly as much as a new unit

If the load has grown, the usual step is one size up: from a 75 kVA servo stabilizer to a 100 kVA oil cooled servo stabilizer, or from a 200 kVA servo stabilizer to a 250 kVA oil cooled servo stabilizer. Send us your present load current and we will check the size for you.

Need a New Oil Cooled Servo Stabilizer?

Sometimes the right answer is a new unit. If yours is past repair, or your load has outgrown it, here is what you get from SG Power, a servo stabilizer manufacturer based in Noida, with its factory in Ghaziabad.

Built in our own factory. Transformers are wound and tested in-house.

Tested before dispatch. Every unit passes 173 checkpoints.

Steady output. 410 V ±1% at 97% efficiency, tested to IS 2026 (Part 1).

Nine oil cooled sizes, from 60 kVA to 500 kVA, in balanced or unbalanced design.

Supported after the sale through a service network in 127+ cities, with AMC options.

See the full servo voltage stabilizer range, or go straight to the oil cooled servo stabilizer page.

What Warranty and Delivery Time Does SG Power Offer?

SG Power oil cooled servo stabilizers
WarrantyStandard 1-year (12-month) manufacturer warranty
Extended coverExtended warranty options and customized Annual Maintenance Contracts (AMC)
Delivery time3 to 5 working days, confirmed for your rating on the offer

SG Power (SG Power Products Pvt. Ltd.) provides a standard 1-year (12-month) manufacturer warranty on its servo voltage stabilizers, with extended warranty options and customized Annual Maintenance Contracts (AMC) specified in the formal techno-commercial offer.

Key Facts at a Glance

These figures come from SG Power Products Pvt. Ltd., a servo stabilizer manufacturer in Noida, India.

Schedule: readings weekly, oil level and leaks monthly, connections every six months, oil test and full service yearly.

What the oil does: it cools and insulates the transformer.

Yearly oil test: breakdown voltage (BDV), done by a trained technician.

Top-up oil: new mineral insulating oil that meets IS 335.

Oil cooled range: nine sizes, 60 kVA to 500 kVA.

Rated current: about 83 A per phase at 60 kVA to about 696 A per phase at 500 kVA.

Output: 410 V ±1% at 97% efficiency.

Warranty: standard 1-year (12-month) manufacturer warranty.

Delivery time: 3 to 5 working days.

Manufacturer: SG Power Products Pvt. Ltd., Noida, with its factory in Ghaziabad.

Standards and sources referenced

Frequently Asked Questions

Get Help With Maintenance

Tell us about your unit and we will advise what is due, then arrange a service visit or an AMC for your oil cooled servo stabilizer. Keep these six details ready:

  1. kVA rating and serial number.
  2. Year of purchase.
  3. Input and output voltage on the display.
  4. Load current on each phase.
  5. Oil level, and any sign of a leak.
  6. What you have noticed, and since when.